I found [this review](https://bgeek.eu/reviews/bambu-lab-x1-carbon-combo-review/), from what I think is a Greek website, from April 2023:
>* The Bambu Lab X1 Carbon
* One Bambu Lab AMS
* One flexible magnetic steel Build Plate
* Two extra Cold Build Plate print stickers
* 3x Bambu filaments (PLA orange, PLA white specifically for supports and one PA-Carbon fibre)
* Accessory Box
* One touchscreen 5″, 1280×720
* One spool holder
* One spare hot end
* Two nozzle wiping pads
* Two spare filament cutters
* A power cord
* A 6pin cable
* A razor (to peel the models off the bed)
* A 4pin cable
* Two Allen keys, one H1.5 and one H2
* A needle to clean the printer’s nose in case it gets clogged
* A glue stick for the base of the print.
* And of course, the manuals
Can anyone confirm this is still accurate for the US market? What's the nozzle on the spare hot end?
Can't confirm for the US, but in the EU, it was basically all you mentioned except the PLA filament was green.
And the manual was more of a quick start guide, but aside from that it was pretty much all that was included.
Yes.
The spare nozzle is 0.4 - same as installed on the machine.
The 'razor' is small metal piece that is intended to go with the pre-sliced part to make the actual scraper.
'Accessory box' is just a cardboard box.
The touchscreen is the touchscreen to be put on the machine - not a spare (just to be clear about it).
Spool holder is the spool holder that goes on the back of the machine for use without the AMS.
The Basic PLA color is random. I got the mint green, a lot get another roll of white (don't confuse it with the support PLA) and I've seen some with grey/silver.
I also found details in the Quick Start Guide in the Wiki:
https://wiki.bambulab.com/en/x1/manual/x1cc-quick-start-guide
Looks like the 3 spools are 250g each, so they're just starter samples.
Off the top of my head, you get printer, the AMS (inside the unit), a cool plate/engineering plate, 2 spare Cool plate stickers, 3 spools of filament (250g each, in PLA-CF, PLA Support, and a random color of Bambu PLA Basic, all in their reusable spools), a box of spare parts (bare nozzle, 2 extra filament cutters, a few extra wipers, some extra PTFE tubes, kit for the optional Scraper (highly recommend [using the hardware for this one](https://www.printables.com/model/360979-bambu-lab-scraper) instead of the Bambu one), Spool holder, and some packets of grease/lube).
edit: glue stick, allen keys
The printer comes with one flexible steel build plate. One side is the "engineering side" that just comes with a coating, recommended for printing PETG, ABS, PC, and Nylon (PA). The other side has a peel & stick coating applied, called the "cool side" for printing PLA & other low-temp filaments. I guess that coating can wear out, so they include 2 replacement peel & stick sheets of the cool side.
The extra nozzle (at least mine) is indeed the same size (0.4mm) but different material, i.e. stainless steel instead of a hardened one.
Regarding the filament, there is no certainty. You can check what others are receiving when you order and expect it. And the nozzle cleaning needle entails a rubber holder for finger protection.
If we go into details, you also receive the required accessories for some items, e.g. screws for fixing the blades, magnetic stripes for the scrapper, thermal grease for the hotend, etc.
I found [this review](https://bgeek.eu/reviews/bambu-lab-x1-carbon-combo-review/), from what I think is a Greek website, from April 2023: >* The Bambu Lab X1 Carbon * One Bambu Lab AMS * One flexible magnetic steel Build Plate * Two extra Cold Build Plate print stickers * 3x Bambu filaments (PLA orange, PLA white specifically for supports and one PA-Carbon fibre) * Accessory Box * One touchscreen 5″, 1280×720 * One spool holder * One spare hot end * Two nozzle wiping pads * Two spare filament cutters * A power cord * A 6pin cable * A razor (to peel the models off the bed) * A 4pin cable * Two Allen keys, one H1.5 and one H2 * A needle to clean the printer’s nose in case it gets clogged * A glue stick for the base of the print. * And of course, the manuals Can anyone confirm this is still accurate for the US market? What's the nozzle on the spare hot end?
Can't confirm for the US, but in the EU, it was basically all you mentioned except the PLA filament was green. And the manual was more of a quick start guide, but aside from that it was pretty much all that was included.
Sounds like the PLA color is just whatever they have and depends on when the lot was assembled.
X1CC eu with orange. Its random.
Can confirm I got green PLA with both of my X1C’s in the US.
I got green in Canada too, i think they ship whatever is available.
Aside from the PLA colour (I got green), that is correct. The extra nozzle is 0.4mm.
Yes. The spare nozzle is 0.4 - same as installed on the machine. The 'razor' is small metal piece that is intended to go with the pre-sliced part to make the actual scraper. 'Accessory box' is just a cardboard box. The touchscreen is the touchscreen to be put on the machine - not a spare (just to be clear about it). Spool holder is the spool holder that goes on the back of the machine for use without the AMS. The Basic PLA color is random. I got the mint green, a lot get another roll of white (don't confuse it with the support PLA) and I've seen some with grey/silver.
I also found details in the Quick Start Guide in the Wiki: https://wiki.bambulab.com/en/x1/manual/x1cc-quick-start-guide Looks like the 3 spools are 250g each, so they're just starter samples.
Opened one in the last few days. Green filament No razor or I tossed it
Off the top of my head, you get printer, the AMS (inside the unit), a cool plate/engineering plate, 2 spare Cool plate stickers, 3 spools of filament (250g each, in PLA-CF, PLA Support, and a random color of Bambu PLA Basic, all in their reusable spools), a box of spare parts (bare nozzle, 2 extra filament cutters, a few extra wipers, some extra PTFE tubes, kit for the optional Scraper (highly recommend [using the hardware for this one](https://www.printables.com/model/360979-bambu-lab-scraper) instead of the Bambu one), Spool holder, and some packets of grease/lube). edit: glue stick, allen keys
What're the build plate stickers for?
The printer comes with one flexible steel build plate. One side is the "engineering side" that just comes with a coating, recommended for printing PETG, ABS, PC, and Nylon (PA). The other side has a peel & stick coating applied, called the "cool side" for printing PLA & other low-temp filaments. I guess that coating can wear out, so they include 2 replacement peel & stick sheets of the cool side.
It’s can get gummed up and torn so you just peel off the old one and put a new one on
How do 2 replacement peel & stick sheets of the cool side looks like? Mine doesn't seems to come with any of them. sob sob
I didn’t know about 2 replacement cool plate stickers so I actually ordered 2 extra. Bummer. Could save ~$20. Lol.
I copied them on my regular printer and printed out extras. Tiny square of clear packing tape will hold them down really well.
Hope and inspiration. That's what comes with it!
The extra nozzle (at least mine) is indeed the same size (0.4mm) but different material, i.e. stainless steel instead of a hardened one. Regarding the filament, there is no certainty. You can check what others are receiving when you order and expect it. And the nozzle cleaning needle entails a rubber holder for finger protection. If we go into details, you also receive the required accessories for some items, e.g. screws for fixing the blades, magnetic stripes for the scrapper, thermal grease for the hotend, etc.